83mm Build Update

Hello everyone welcome back.

Todays video is an update on the new 83mm brushless build I have been working on. I added a new camera mount. New standoffs so its not so tall. I also added motor guards and landing gear.

Here are the full specs for the build

BetaFPV 83mm Carbon Fiber Frame
Recommend motors: 1102 1103 1104 brushless motors
Wheelbase: 83mm
Plate Thickness:2.0mm
Weight: 10g
Form Factor: 16mm x 16mm


USAQ Betaflight F3 Micro 6A 2S 4-In-1 Brushless ESC OSD Flight Controller Micro Cube
Flight Controller Specifications:
Dimensions: 20*20mm
Mounting Dimensions: 16*16mm
Weight: 1.9g
Processor: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000 ( connected by SPI)
Firmware version: betaflight_3.1.0_OMNIBUS
Built-in BEC: 5V/0.5A
Receiver: PPM, Spektrum 1024/2048, SBUS, IBUS, XBUS, SumD SumH RX etc.
Power supply: 2S lipo battery ( 6.5V-8.4V)
Suitable for 60mm-80mm mini brushless FPV Quadcopter frame

ESC Specifications:
Item name: 4 In 1 6A BLHeli_S ESC
Size: 25x29mm (includes solder pad)
Mounting holes: 16x16mm, φ2mm
Weight: 3g
Input voltage: 2S lipo
Con. Current: 6A
Peak Current: 10A (5S)
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Driver: 3 in 1 MOS
Supports Dshot Oneshot multishot

-Support programmable LED Sprit (turn off transponder before using)
-Support BLheli/BLHELI_S suite Pass-through ready
-Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
-Default Dshot600
-Built-in voltage detection, alarm
-Built-in Betaflight-OSD
-Buzzer solder pin
-LED_STRIP connector

Package included:
1* Super_S F3 flight control board
1* Super_S BS06D 6A 4in1 ESC
8*M2*5+5 Nylon column
8*M2 Nuts
8*M2 Screw


BetaFPV 1103b 10,000kv Brushless Motors
Height: 15mm
Width: 13.6mm
Weight: about 3.7g
Shaft: 1.5mm
KV: 10000KV

No longer available via BetaFPV. Here are some similar motors


BetaFPV 1735 4 Blade Props
Material: PC plastic
Length: 1.7 inch, about 43.2mm
Color: white, orange, purple, green, blue, red
Mounting hole: 1.5mm
Weight: 0.8g per piece
Applicable for 1102, 1103, 1104, 1105, 1106, 11xx motors


BetaFPV H01 AIO FPV Camera
Output power: 25mW
Supply Voltage: 2.9-5.5v
Weight: 3.6g
Antenna: Dipole
Frequency: 5.8GHz 40 Channels
FOV: 120


M2 Standoff kit

Motor Guards by Makerfire

Camera mount for 16mmx16mm by RJX Hobby

BetaFPV 450mah 2s Lipos


If you have any questions about this build feel free to leave me a comment.


Thanks for watching

Fly Safe & Fly Often


Music by Ryan Little
Sub his channel



Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Blog at WordPress.com.

Up ↑

%d bloggers like this: